dido:public:ra:xapend:xapend.b_stds:tech:iso:7816-10
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
dido:public:ra:xapend:xapend.b_stds:tech:iso:7816-10 [2021/06/24 15:55] nick |
dido:public:ra:xapend:xapend.b_stds:tech:iso:7816-10 [2021/08/06 17:23] (current) murphy [Scope] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ===== ISO/IEC 7816-10 Identification cards — Integrated circuit(s) cards with contacts — Part 10: Electronic signals and answer to reset for synchronous cards ===== | ===== ISO/IEC 7816-10 Identification cards — Integrated circuit(s) cards with contacts — Part 10: Electronic signals and answer to reset for synchronous cards ===== | ||
| - | [[dido:public:ra:xapend:xapend.b_stds:tech:iso| return to the ISO Standards ]] | + | [[dido:public:ra:xapend:xapend.b_stds:tech:iso:start| return to the ISO Standards ]] |
| <table> | <table> | ||
| - | <caption>Data sheet for Identification cards — Integrated circuit(s) cards with contacts — Part 10: Electronic signals and answer to reset for synchronous cards</caption> | + | <caption>Data sheet for [[dido:public:ra:xapend:xapend.a_glossary:i:identification|Identification]] cards — Integrated circuit(s) cards with contacts — Part 10: Electronic signals and answer to reset for synchronous cards</caption> |
| | Title | Identification cards — Integrated circuit(s) cards with contacts — Part 10: Electronic signals and answer to reset for synchronous cards | | | Title | Identification cards — Integrated circuit(s) cards with contacts — Part 10: Electronic signals and answer to reset for synchronous cards | | ||
| | Acronym | | | | Acronym | | | ||
| Line 15: | Line 15: | ||
| ==== Scope ==== | ==== Scope ==== | ||
| - | This part of ISO/IEC 7816 specifies the power, signal structures, and the structure for the answer to reset between an integrated circuit(s) card with synchronous transmission and an interface device such as a terminal. | + | This part of ISO/IEC 7816 specifies the power, signal structures, and the structure for the answer to reset between an integrated circuit(s) card with synchronous transmission and an [[dido:public:ra:xapend:xapend.a_glossary:i:interface|interface]] device such as a terminal. |
| The specifications in [[dido:public:ra:xapend:xapend.b_stds:tech:iso:7816-3]] apply where appropriate unless otherwise stated here. | The specifications in [[dido:public:ra:xapend:xapend.b_stds:tech:iso:7816-3]] apply where appropriate unless otherwise stated here. | ||
| Line 22: | Line 22: | ||
| This part of ISO/IEC 7816 specifies two types of synchronous cards: type 1 and type 2. | This part of ISO/IEC 7816 specifies two types of synchronous cards: type 1 and type 2. | ||
| + | |||
| + | |||
| + | /**=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- | ||
| + | /* To add a discussion page to this page, comment out the line that says | ||
| + | ~~DISCUSSION:off~~ | ||
| + | */ | ||
| + | ~~DISCUSSION:on|Outstanding Issues~~ | ||
| + | ~~DISCUSSION:off~~ | ||
dido/public/ra/xapend/xapend.b_stds/tech/iso/7816-10.1624564558.txt.gz · Last modified: 2021/06/24 15:55 by nick
